A&V WATERJET TECH INC. (262) 250-8100
|
A&V WATERJET TECH INC. (262) 250-8100 |
==================================================================================================== |
|||
|
|
|||
==================================================================================================== |
|||
|
How much do I have to spend on a waterjet cutting system? A&V Waterjet Tech Inc. offers new waterjet cutting machines starting with $40K only. What are the advantages of waterjet cutting? A waterjet is a versatile and flexible machining tool. You can cut various materials efficiently and cost-effectively and you can create varous parts as well
What are the advantages of waterjet cutting comparing with lasers? Laser cutting is a very productive process and certainly has its market. However, waterjets do have several advantages compare with lasers:
What are the advantages of waterjet cutting comparing with EDM? EDM is extremely accurate, but very slow. It also requires an electronically conducive material and produces a heat-affected zone. For many applications, Dynamic Waterjet technology can produce parts approximating the accuracy of EDM for a fraction of the cost and time. What are the advantages of waterjet cutting comparing with milling? If you are through-cutting the periphery and holes, rather than blind holes, pockets, and threads, the abrasive waterjet is typically much faster, easier to program and cheaper than milling. This is largely due to the fact that we cut a part with one pass, and we do not have to reduce all the metal to chip form. In addition, the scrap is usually more valuable in solid form than chip form. What are the advantages of waterjet cutting comparing with plasma? Obviously, plasma is a hot process. It adds a great deal of heat to the product, leaving a heat-affected zone. The surface finish of the abrasive waterjet is generally better. It leaves no dross on the backside of the part, reducing secondary operation. Abrasive waterjets have no thickness limitation , and can be much more closely nested. What tolerances can we expect from waterjet cutting? Over 80% of the world's abasivejet users cut parts to ±0.003-in. or looser accuracy. However, there is a percentage of users who cut parts to tolerances as tight as ±0.001 and even ±0.0005in. The accuracy you will get depends on whether or not you have Dynamic Waterjet technology, the accuracy of the machine, part size and part thickness. Should I cut underwater? Cutting underwater will do a couple of good things for you. First, it will reduce the noise of the cutting process to under 75 dB. Second, it will eliminate the frosting of the top surface of the material within 1/16" of the jet (it can also be helpful if one is able to pass low-pressure water over the mixing tube). The down side of cutting underwater is that you can't see the cutting process. You also have to work underwater for material handling, unless you have water level control on your catcher. How thick can it cut? Up to 8-in. thick steel and titanium are cut on a production basis. There have been cases where 12" and even 15" thick material has been cut. The vast majority of users, however, cut between 1/4" to 2" thick materials. What kind of abrasive are you using? Garnet is by far the most commonly used abrasive material. Users have found garnet to be the best for them in terms of cost, cut speed, mixing tube life, and health hazards. Other abrasives include olivine sand, aluminum oxide, and some man-made materials. At what pressure do you cut? 90,000 psi is the maximum intensifier pump pressure. It has been proven that the fastest and most efficient cutting is done at the highest cutting pressure. While it is true than higher pressures can result in slightly increased maintenance on intensifier pump seals, for well designed equipment however, the very slight increase in maintenance cost is more than offset by the large increase in cut speed. Remember, the largest costs involved in abrasive waterjets are the labor, abrasive, and depreciation, not the pump seals. What taper can I expect? With a Dynamic Waterjet system, you will experience virtually no taper. In the case of conventional waterjet cutting, the taper you get is a function of the cut speed. However, the worst taper you will get will be equal to the maximum kerf width at the top (example: 0.035") and 0.000". at the bottom. As you slow down the taper will be reduced until you get parallel sides. Most tapers you see on precise cuts are 0.002" to 0.004" on a side. How much water will you use when cutting at 55,000 psi?
Each 0.010" orifice uses 0.5 gpm. How long before maintenance is required on the pump? You can expect around 400 to 1200 hours of cutting time before needing to replace the high-pressure seals on a 55,000 psi intensifier and 200 to 600 hours before needing to replace the seals in pump. What stops the jet? In most waterjet systems 36 inches of water in the catchers dissipates the energy of the jet. How long does the material support last? You can expect hundreds of hours of use from the support grating before needing to replace it, as long as you don't cut just one pattern over the same section for thousands of parts. Slats and grates can be shifted, swapped, and flipped just as with plasma and laser cutting, thereby extending the life of the supports. How long does the mixing tube last? The highest quality ceramic carbide mixing tubes last 30% longer than other mixing tubes. A tube such as this can deliver 150 hours of cutting time for 0.020" of growth in the diameter. Many users keep the mixing tubes longer and use them to cut parts which require looser tolerances. How much abrasive is used? For the most efficient cutting, cutting heads on a 55,000 psi intensifier use:
Are the waterjets hard to program? Waterjets are no harder to program with standard CNC equipment than any other cutting process. With standard CAM software, converting DXF to cutting program is quick and easy, with only speed changes for material changes. With the PC based control software such as FlowMaster, programming for abrasive waterjets is easier and quicker than any other process. All the guess work is gone. This means projects are programmed and cut quickly and accurately. What fixturing is required? Since the force exerted on the workpiece is very small (under 1 lb. for precision cuts and under 5 lbs. for average cuts), the need for very large, stiff fixtures is eliminated. Many customers use simple weights to hold the parts in place. What are the operating costs of a waterjet? Hourly costs range from about $19 per hour for the small head (0.010/0.030), up to $35 per hour for the large head (0.016/0.040). This includes all costs related to the machine, but does not include labor, lease, and depreciation. What is the cost of the abrasive? Abrasive will cost between $0.16 per pound to $0.40 per pound delivered, depending on the type and quantity you purchase. How loud is it? Noise from the waterjet is dependent upon the distance the supersonic jet is exposed to the open air. If you are cutting underwater, the noise level will be under 75 dB. If you are cutting above water, and especially if there is a large distance between the mixing tube and the work piece, the noise will be much higher, up to 95 dB. In these cases, most customers enclose the entire work area. How do we dispose of water/garnet? Neither water nor garnet are toxic or hazardous in any way. The water, when properly filtered for turbidity, can be put down the drain. The garnet waste can usually be dumped in a standard landfill. Of course, if the material you are cutting is toxic or hazardous, the waste generated may be hazardous. Please see your local utilities for specific requirements. Is this pure water? It is clean water. Most of our customers use softened tap water. Intensifier pumps should be supplied with filter cartridges that clean the water down to 0.5 micron. De-ionized or reverse osmosis systems are generally not recommended. These types of systems can make the water too clean, which makes the water aggressive and harmful to the pump. Do you recycle the water? Recycling systems are available. However, because waterjet systems use a low amount of water it is not economically viable for most users. |
|||
 |
|
|